Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Specifications
   2.2. Arrangement of knots and units
   + 2.3. Frequency of maintenance and types of procedural works
   2.4. Intensive service
   + 2.5. Check of level of liquids
   2.6. Check of tires
   2.7. Check of level of liquid in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of a steering
   2.9. Replacement of oil in the engine and an oil filter
   2.10. Care of the battery
   2.11. Check of the cooling system
   2.12. Check of a condition of the hoses located in a motor compartment
   2.13. Screen wiper brushes
   2.14. Shift of wheels
   2.15. Check of a suspension bracket of a steering
   2.16. Greasing of a running gear, suspension brackets, steering and details of a body
   2.17. Check of an exhaust system
   2.18. Check of level of oil in a manual transmission
   2.19. Check of level of oil in a transfer case
   2.20. Check of level of oil in a reducer
   2.21. Check of seat belts
   2.22. Check of covers of half shafts
   2.23. Zolotnik of ventilation of a case
   2.24. The filtering element of the air filter
   2.25. Belts of the drive of hinged units
   2.26. Check of fuel system
   2.27. Check of wear of brakes
   2.28. Check and adjustment of pedals of coupling (brake)
   2.29. Replacement of candles
   2.30. Check and adjustment of gaps in valves
   2.31. Replacement of the fuel filter
   2.32. High-voltage wires, runner and cover of the distributor
   2.33. Care of the cooling system
   2.34. Naves and bearings of forward wheels
   2.35. Replacement of liquid in automatic transmission and the filter
   + 2.36. Oil replacement
   2.37. Check of a tank with an absorber
   2.38. Valve check of system of recirculation
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes

2.9. Replacement of oil in the engine and an oil filter

1. For ensuring access to the lower part of the car, it needs to be established on two supports, either to lift a telfer, or to come around on a hole or a platform.
2. The car has to be in horizontal situation, the engine has to be heated-up.
3. Turn off a stopper of a maslozalivny mouth.
4. Substitute the pallet, clear and turn off a drain stopper. Merge oil.
5. Clear and tighten a drain stopper.
6. Substitute a vessel under an oil filter, lower the car.
7. By means of a special key release an oil filter then turn out it hands. Immediately incline the filter and merge oil in a vessel.
8. Carefully wipe pure rags a filter prileganiye place on the engine.
9. Slightly oil a sealing ring of the new filter for the engine and wrap the filter into place. Tighten the filter by hand.
10. At first fill in a half of volume of oil then wait some minutes that all oil flew down in the pallet. Continue to add oil in the small portions, before achievement of a mark "H" in the probe.
11. Start the engine and on the working engine check tightness of a stopper of the pallet and filter, having tracked these places within several minutes.
12. Stop the engine and wait some minutes that oil flew down in the pallet. Again check oil level. After filling of all channels and the filter the level of oil can go down. If necessary add oil to a mark "H".