Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car



Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
- 11. Electric equipment
   11.1. Specifications
   11.2. Battery
   + 11.3. System of ignition
   11.4. Ignition coil(s)
   11.5. Ignition distributor
   11.6. Check and installation of the moment of ignition
   11.7. Block of electronic ignition
   11.8. Induction sensor
   + 11.9. System of a charge of the battery
   + 11.10. Generator
   11.11. System of start-up of the engine
   + 11.12. Starter electric motor
   11.13. Traction relay
   11.14. Check of tension
   11.15. Detection of short circuit
   11.16. Check of reliability of grounding
   11.17. Check of integrity of a chain
   11.18. Finding of not closed chain
   11.19. Search of malfunctions
   11.20. Safety locks
   11.21. Fusible crossing points
   11.22. Breakers
   11.23. Relay
   11.24. Breaker of indexes of turn / alarm system
   11.25. Switch of indexes of turn
   11.26. Lock of ignition and drum of the lock
   11.27. Switch of external lighting
   11.28. Screen wiper switch
   11.29. Lamps of headlights
   11.30. Adjustment of headlights
   11.31. Headlight case
   11.32. Replacement of lamps
   11.33. Receiver and loudspeakers
   11.34. Antenna
   + 11.35. Screen wiper electric motor
   11.36. Switch of heating of back glass
   11.37. Heater of back glass
   11.38. Guard of devices
   11.39. Sound signal
   11.40. Electric drive of mirrors
   11.41. Cruise control
   + 11.42. Window regulator electric drive
   11.43. Electric drive of door locks
   11.44. Safety cushions
+ 12. Electroschemes





11.34. Antenna

GENERAL INFORMATION

Prevention

On part of cars "Toyotas 4 Runner/Hilux/Surf" the printing antenna is installed, all works on which service are performed in car service.


Removal and installation

PERFORMANCE ORDER
1. Remove the receiver and disconnect the plug. Disconnect all latches and brackets on the route of the antenna. Attach a wire (cord) about 1,5 m long to the antenna.
Stationary antenna
2. Turn off an antenna mast.
3. Turn off a basis nut, disconnect the basis and extend a cable so that the auxiliary wire seemed.
4. Attach a wire to a cable of the new antenna and involve a cable.
5. Installation is carried out upside-down.
The antenna with the electric drive

Prevention

Works are performed together.


6. Transfer the ignition key to the situation LOCK.
7. Turn off an antenna basis nut.
8. Working at the same time (together with the assistant), press the AM/FM buttons of the receiver and transfer the ignition key to situation ASS, – at this moment it is necessary to hold the antenna. The antenna will start and completely will leave the electric motor winch. Remove a mast, the ignition key has to be in situation ASSORTMENT still.
9. Remove three latches (are specified by shooters) the internal panel of a wheel niche in an aperture between a wheel and a wing, get the panel, disconnect the socket.
10. Turn off a bolt of fastening and remove the antenna electric motor.
11. Attach a wire to a cable of the new antenna and involve a cable in salon.
12. Install the electric motor.
13. Establish an antenna mast so that teeth on a cable were turned forward.
14. Wind a cable and involve a mast for what transfer the ignition key to the situation LOCK (if the key was already transferred to this situation from situation ASS, execute actions (see item 8). If the cable is not taken up, rotate it in the direction of an arrow.
15. Wrap a basis nut even if the mast completely was not involved. Press the buttons of a choice of ranges on the receiver and the antenna will be involved.
16. Further installation is carried out upside-down.