Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
- 7. Transmission elements
7.1. Specifications
- 7.2. Coupling
7.2.1. Main cylinder of coupling
7.2.2. Working cylinder of coupling
7.2.3. Coupling details
7.2.4. Vyzhimna bearing
7.2.5. The directing bearing
7.2.6. Coupling hydraulic actuator
7.2.7. Coupling pedal
7.2.8. The blocking coupling switch
+ 7.3. Cardan shaft and cardan hinges
7.4. Back and forward axes
7.5. Bearing, epiploon and half shaft of the back bridge
7.6. Epiploon of a reducer of the back bridge and forward axis
7.7. Zadny Bridge
7.8. Forward half shafts
7.9. Replacement of covers and dismantling of the CV JOINT
+ 7.10. Electromagnetic drive of a forward leading axis (ADD system)
7.11. Forward reducer
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes
|
The switch is intended for blocking of start-up of the engine if the pedal of coupling is not squeezed out.
|
|
The blocking coupling switch (it is specified by an arrow) is mounted on an arm in the top part of a pedal, fastens 2 nuts by which its situation concerning a pedal is regulated. |
Check, adjustment and replacement
| PERFORMANCE ORDER |
| 1. Be convinced that the engine is started only at the squeezed-out pedal. |
| 2. Otherwise the switch is faulty. Check presence of tension on the switch. |
| 3. If tension is, check connection with the mass of the second conclusion of the switch at the released pedal. |
| 4. If the chain of the switch is faulty, eliminate malfunction and again check the switch. |
|
5. If the chain is serviceable, check short circuit of contacts of the switch. At the pressed pusher contacts have to become isolated, at the released pusher contacts are disconnected. Otherwise replace the switch. |
|
START UNBLOCKING SWITCH
This switch provides start of the engine without pressing a coupling pedal that can be necessary in the complicated traffic conditions (for example uphill). The button of the switch is on the left side on the forward panel, the canceling switch is part of blocking coupling switch.
Check, adjustment and replacement
| PERFORMANCE ORDER |
|
1. Transfer the button to the situation Off and prisoyediyenit (+) – an ohmmeter conclusion to a conclusion 2 switches, and (-) – an ohmmeter conclusion – to a conclusion 1. Between these conclusions the ohmmeter has to show a gap. |
| 2. In the same position of the button prisoyediyenit (+) – an ohmmeter conclusion to a conclusion 3 switches, and (-) – an ohmmeter conclusion – to a conclusion 1. Between these conclusions the ohmmeter has to show a gap. The chain also should not be between conclusions 2 and 3. |
|
3. Give food + 12B on a conclusion 3, and (-) attach batteries to a conclusion 1 (+) – a conclusion of an ohmmeter attach to a conclusion 2 switches, and (-) – an ohmmeter conclusion – to a conclusion 1. At the pressed button () between these conclusions the ohmmeter has to show a chain in the provision On. |
| 4. When the switch is in the family way Off between these conclusions the gap has to be. |
| 5. Disconnect the battery and transfer the switch to the situation On. Between conclusions 1 and the 2nd ohmmeter has to show a gap. |
| 6. If results of checks differ from described above, replace the switch. |
| 7. For adjustment release a lock-nut and rotate the switch to a pusher vystupaniye on 7,5–8,3 mm concerning a lock-nut. |
| 8. For replacement remove the lower facing, disconnect the socket, turn off a lock-nut and remove the switch. Installation is carried out upside-down. |
|
|
|