Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car


Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. 4-cylinder engines
      3.1.1. Specifications
      3.1.2. The types of repair which are carried out without removal of the engine from the car
      3.1.3. Installation of the piston of the 1st cylinder in compression step VMT
      3.1.4. Cover of a head of cylinders
      3.1.5. The soaking-up collector
      3.1.6. Final collector
      3.1.7. Cam-shafts and pushers
      3.1.8. Head of cylinders
      3.1.9. Cover of the chain drive of cam-shafts
      3.1.10. Forward epiploon of the crankshaft
      3.1.11. Oil pallet
      3.1.12. Oil pump
      3.1.13. Flywheel (leading disk of the hydrotransformer)
      3.1.14. Back epiploon of the crankshaft
      3.1.15. Engine mount details
   + 3.2. V6 3,0 engines of l (1993-1994) and 3,4 l (since 1995)
   + 3.3. Dismantle and capital repairs of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes





3.1.9. Cover of the chain drive of cam-shafts
GENERAL INFORMATION

Details of forward part of the engine
1. Perepuskny pipe of N1 cooling liquid
2. Provladka
3. Uspokoitel N2
4. Natyazhitel N2
5. Uspokoitel N3
6. Uspokoitel N4
7. Oil receiver
8. Pallet
9. Guard
10. Arm
11. Generator
12. Adjusting arm
13. Epiploon
14. Pulley
15. Krylchatka with a hydraulic actuator
 16. Pulley of the pump of cooling liquid
17. Chain cover
18. Leading gear wheel of a chain of a cam-shaft
19. Leading asterisk of the N2 crankshaft
20. Roller of the leading gear wheel of a balansirny shaft
21. Leading gear wheel of a balansirny shaft
22. Chain of a balansirny vl
23. Cam-shaft asterisk
24. Boot of a natyazhitel
25. Cam-shaft chain
26. Uspokoitel N1
27. Compressor
28. Arm
29. Sensor of rotation of the crankshaft
30. Ring laying

Designation of the chain cover bolts differing in the sizes

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Merge oil and cooling liquid.
3. Lift a car front.
4. Remove the lower guards.
5. Remove a broad tank of a radiator.
6. Turn out candles and take off all belts of the drive.
7. Otrvernuv bolts (are specified by shooters), remove the compressor of the conditioner and take aside, without disconnecting from the highway.
8. Remove the generator, a roller of a natyazhitel and an arm (bolts of the lower arm are specified by shooters).
9. Remove the drive cruise control (if it is provided).
10. Disconnect the lower hose of a radiator and remove the pump of cooling liquid.
11. Install the piston of the 1st cylinder in compression step VMT.
12. Remove a head of cylinders.
13. Remove the pallet.
14. Record a crankshaft pulley to turn off a bolt.
15. Turn off a bolt and remove a crankshaft pulley.
16. Turn off bolts (shooters) and nuts of a cover of a chain.
17. Carefully uncover.
18. Remove a chain and an asterisk.
19. Remove uspokoitel and details of a natyazhitel.

Check

PERFORMANCE ORDER
1. Check a condition of a chain and uspokoitel. Replace worn-out details. In case of strong wear of uspokoitel remove and clear the pallet and an oil receiver.
2. Check work of a plunger. The plunger has to move freely at the taken-away clamp.
3. Check work of a clamp of a natyazhitel. The clamp has to hold a plunger reliably.
4. Check purity of a jet of an oil nozzle.

Installation

PERFORMANCE ORDER
1. Clear forward part of the engine, a chain and a cover, establish a nozzle. The nozzle has to be turned towards a chain.
2. Put on a chain a cam-shaft asterisk, having combined links with distinctive tags on the leader and conducted asterisks. Press out a chain, having tied up a strong tape.
3. Combine a link with a distinctive tag (it is specified by an arrow) with a groove under a crankshaft spline (it is specified by an arrow) and put on the leading asterisk.
4. Apply the sealant roller on a cover, be convinced available all laying and establish a cover (within no more than 5 min. after drawing), having entered the roller of the leading rotor of the oil pump into gearing with the leading gear wheel of the crankshaft.
5. Wrap bolts and tighten with the set moment (see subsection 3.1.1). The bolts of fastening of a cover of a chain differing in the sizes are specified rice. Designation of the chain cover bolts differing in the sizes. Remove a chain binding.
6. Establish other details upside-down. Be convinced of correctness of installation of a cover, fill the cooling system with liquid, fill in oil. Start the engine, be convinced of lack of a leak. Determine the moment of ignition and carry out test of road performance of the car.