Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and operation of the car

Toyota 4ranner
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. 4-cylinder engines
      3.1.1. Specifications
      3.1.2. The types of repair which are carried out without removal of the engine from the car
      3.1.3. Installation of the piston of the 1st cylinder in compression step VMT
      3.1.4. Cover of a head of cylinders
      3.1.5. The soaking-up collector
      3.1.6. Final collector
      3.1.7. Cam-shafts and pushers
      3.1.8. Head of cylinders
      3.1.9. Cover of the chain drive of cam-shafts
      3.1.10. Forward epiploon of the crankshaft
      3.1.11. Oil pallet
      3.1.12. Oil pump
      3.1.13. Flywheel (leading disk of the hydrotransformer)
      3.1.14. Back epiploon of the crankshaft
      3.1.15. Engine mount details
   + 3.2. V6 3,0 engines of l (1993-1994) and 3,4 l (since 1995)
   + 3.3. Dismantle and capital repairs of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes

3.1.3. Installation of the piston of the 1st cylinder in compression step VMT

GENERAL INFORMATION

Prevention

It is meant that works are performed at the correct installation of the distributor of ignition (if the distributor is provided). If it is necessary to redeem the correct situation of the distributor, determine an engine step by feeling of a compression in the 1st cylinder by the turned-out candlelight then combine ignition moment tags (see below).

Installation of the piston of the 1st cylinder in VMT of a step of compression is necessary for performance of adjusting and adjustment works (adjustment of valves, installation of the moment of ignition, etc.).

PERFORMANCE ORDER

1. Transfer the selector to the situation Neutral or Park (on and/t) or in neutral situation (on a manual transmission). Disconnect sockets from the coil (coils) of ignition.
System of ignition with the distributor
2. On a wire from a candle of the 1st cylinder (or according to the enclosed scheme) find the corresponding conclusion on a cover of the distributor of ignition and designate risky on the case. Uncover the distributor.
	3. Turn the crankshaft a key for a pulley bolt head clockwise before combination risks on a crankshaft pulley with a tag "0" on a motionless scale.
4. If the index of the runner of the distributor is opposite risks on the distributor case, the piston of the 1st cylinder is in compression step VMT. If the runner is turned on 180 ° from risks, turn the crankshaft on 1 turn then the piston of the 1st cylinder will be exposed in compression step VMT.
	5. Thus tags on a scale and a pulley have to be combined, and the index of the runner has to be opposite risks, designating a conclusion of the 1st cylinder.
6. Designate conclusions of other wires according to an engine operating procedure. Turning the crankshaft further clockwise concerning position VMT of the 1st cylinder, it is possible to expose the piston of each cylinder in VMT, combining the index of the runner with tags of conclusions.
System of ignition without distributor (engines of 1998)
7. Turn out a candle of the 1st cylinder and attach the compression measuring instrument through a hose about 150 mm long, having screwed the hose union in an opening for a candle.
8. Turn the crankshaft until pressure of a compression does not start increasing in process of rapprochement of tags on a pulley and on a scale. Having passed tags, remove the measuring instrument and turn further the crankshaft on 2 turns.
Prevention The most exact installation of the piston in compression step VMT on such engines is reached by simultaneous combination of tags on a pulley of the crankshaft and on asterisks of cam-shafts (see subsection 3.1.7).